How much does driveway asphalt paving cost?
When picking driveway paving materials it is vital to match upfront prices to long-term costs. Some paving materials are extremely affordable to install, but need regular maintenance and need to be changed in just a few years. While other paving materials are costly to install, they need little maintenance and will last a lifetime.
How much does a driveway cost?
The national average cost of asphalt driveway is near to $4,500. The price can fall or rise depending on lots of factors including quality of material, location, depth of material needed, and the size of your drive.
Asphalt driveway installation pricing across Canada and the USA can be anywhere from $1,500 to $10,000, but most spend $5,000 to $8.000. The amount varies depending on such factors as the labor cost and the general difference between pricing in different states.
Asphalt Driveway Paving Prices
· The average cost of asphalt driveway paving is between $2 and $5 per square foot.
· Total driveway paving cost will change from area to area consistent with local labor costs and material.
· Most gravel driveways are made of crushed gravel or stone which costs approximately $25 – $30 per ton plus $100 or so for delivery per load. For a small, 15ft x 20ft by three inch deep driveway, five tons should be more than enough at a full cost of approximately $250. For a thicker base or larger driveway, the cost will be higher. For example, a driveway 15 x 700 feet long with a 6 inch base will need approximately twenty-five tons of gravel, at a material cost of about $710. With delivery, the full cost will be around $1000.
· A concrete driveway ninety feet long and ten feet wide would be around $1800 for material with an extra $2000 or so for labor, for a full cost of nearly $4000.
· A Macadam driveway, also called tar and chip, consists of gravel sprayed or crushed stone. They cost around $2 – $5 per square foot.
· Another big option is a cobblestone driveway. At approximately $5 per price and 1000s required per driveway, plus labor at around $40 – $60 per square foot, this can be very costly.
· A brick driveway begins at around $1.50 per brick plus the installation cost. For a longer driveway which may need as much as 20,000 bricks, the material costs alone could be $20 – $30,000, additional $10 – $30 per square foot for labor.
· Most expert contractors can install concrete, gravel or asphalt driveway in a day. Brick and cobblestone need considerably more work and could take a week or more to install depending on the driveway size.
· Concrete and asphalt driveways need to be resealed regularly. For asphalt in areas with cold, hot or wet weather, this may need to be performed every year. In moderate climates every 3 to 10 years might be sufficient.
· Concrete averages about 5 years before it needs resealing. A cost guess for driveway resealing is between 20 and 80 cents per square foot. For a one-thousand square foot driveway this costs a total of $120 – $180.
· Driveways with curves, slopes, or that are otherwise hard to surface will cost more in labor.
· Removing an existing driveway costs $50 – $60 per hour.
Other consideration and costs
· These prices are for service in the quick service area of the provider.
· Permit fees and taxes are not added
· Extra hand-excavation of typical soil will generally be around $50 per cubic yard.
· Typical extra residential site cleaning and preparation jobs range in cost from $0.50 to $1.50 per sq. ft. depending on the size and amount of material, and transport.
FAQs
How long does it take to install an asphalt driveway?
It should take approximately 1 to 2 days for a one driveway, but this can extend to around 4 to 5 days for a more substantial area.
How long until I can drive on my newly built asphalt driveway?
You will need to be patient for around 1 to 7 days before parking your vehicle or your new driveway. Just to be on the safe side, it is advised to leave it at least 3 days.
Do I need permission for an asphalt driveway?
Whether or not you need planning permission for a new driveway generally depends on the drainage condition. If you have not installed drainage or don’t use porous material, and extra water will drain onto public areas, you are likely to need planning permission. It is excellent to speak to your local authority for more suggestions.
Can you pave over an existing asphalt driveway?
Yes, you can easily pave over. Anyway, whether or not you should do so will depend on the situation of the current asphalt. If there are many deep cracks or an unstable foundation, replacement is the excellent choice.
How do you apply asphalt sealant?
Asphalt sealant needs to be applied every three to five years. The best news is that this is well within the scope of the average homeowner. The temperature should be 45 degrees warmer or Fahrenheit, and you will need at least 3 days without rain.
First, you will need to sweep the driveway. Use a dish soap and hose to clean the driveway of debris and dirt, and then let it dry. If there are any cracks, use an asphalt cracks sealer and then let it dry before sealing.
Combine the sealant by turning the can upside down. Once the can is opened, stir to make sure of the right mixing, begin with one corner, and pour out a little amount of sealer. Spread it on the surface with a squeegee.
End words
The average cost of asphalt driveway paving can cost as low as $3,085 and as high as $7,910 with an average cost ranging around $5,000. There are extra factors, such the asphalt type, the quantity needed, the labor costs and others that can affect the full cost of paving an asphalt driveway. It is highly advised to talk to professional pavers, for a reliable and durable asphalt driveway that will last for years to come.